Install the Tiles.

How to Tile

how to tile flooring. There are several ways depending on the surface that will be installed and the expertise of a technician that is installed with this primary methods are 2 methods.

1 The installation by using the limestone sand is the method that is suitable for the area that does not have to adjust the level and its polished

1.1. Check the tiles before the crabs check the type of color tiles of the tiles of the same color or not. The warpage in the values that can be laid out or not. If they find something that is abnormal, contact your sales representative immediately.

1.2. Clean the area to be tiled

1.3 should be tiled unless the grout 2-3 mm value by the standard of the factory.

1.4 should be fully tiled in the same way by observing the arrow back the tiles

1.5. Check the level with the thickness for a mixture of limestone sand are tiled in between 3-5 cm (not including the thickness of the tiles) If more or less than to edit (the page of the limestone sand may change according to the limitations of the area which is in the judgment of the tiled)

1.6. Mix the limestone water sand in the ratio of 1 liter of water and 4 kilograms and sand 8 kilograms (the amount of water can be reduced if the sand and the humidity is much)

1.7 apply these ingredients into the area will install the tiles to adjust to the level before you remove the tile to install the

1.8 is laid out along the arrow should be fully tiled in the same direction as the arrow or the logo on the back of the tile using the adhesive cement and water painted on the back of the tiles or use collaboration and limestone on the back of the tiles lift the tiles on the plaster that use a rubber mallet and tap lightly to level.

1.9 To place the tile and the seams are in the same orientation unless the grout at least 2-3 cm(should use the spacer device align the tiles) when the crabs are completed and allow to reset the limestone for approximately 72 hours prior to the medication

1.10 after the reset limestone, make the medication to prevent soil accumulation along the tiles by cleaning the seam of the tiles with the use of a needle or brush hard, next to use the material of the compression, Full to not have the foam and cavitation

Caution

- Do not install the tiles by the way, the dumplings or wet limestone the meat from the Tiles has more body may cause the collapse are not equal and have air pockets as a space under the floor tiles, Tiles gliders and brittle

Note

- The ingredients of the cement adhesive Collaboration Solution limestone and the material of medication, please ask the manufacturer to prevent the error later.

- To maintain the beauty of the background to the installation is completed should be covered with plastic or cardboard to prevent scratches and dirt

- before you use it should be clean (WAX) using scouring powder wax lime or ground gypsum board, rinse with clean water or cleaning solution that is medium sized should not use the solution that has the ingredients of the acid such as the hibernate chloric acid (salt) Nitric Acid (Nitrous Acid) Sulfuric Acid (sulfuric acid.) The hibernate fluorescent metric (hydrofluoric acid) and should not use chemical type of isopropyl (alcohol) to clean

2 The installation by using the adhesive cement

Is another way that is fast and convenient for the area of the successfully. Because the adhesive cement is the man of the cement Porto Strickland, sand and composite material and other special

2.1, check the tiles before the crabs check, Nick tiles. The color of the tiles of the same color or not. The warpage in the values that can be laid out or not. If they find something that is abnormal, contact your sales representative immediately.

2.2. Clean the area to be tiled

2.3 should be tiled unless the grout 2-3 mm value by the standard of the factory.

2.4 should be fully tiled in the same way by observing the arrow back the tiles

2.5. Check the level of the area that will make the tiles to level. According to if greater than or less than the edit

2.6 mixed glue to cement the and the way of the manufacturer of the adhesive cement in general the adhesive cement 1 bag (15-20kg) to water. 3-5 L, and then each brand specify

2.7 The cement adhesive on the floor, enough for the tiles to be installed. Use the comb teeth to dislodge the fish to the groove across the including the back of the tile to be installed with (the number of the comb on the model, the adhesive brand of cement used), and then remove the tile on the adhesive cement by the spool in the direction of the arrow after tapping the tile with a rubber mallet gently so that it is level

2.8 to the Tile and the evidence in the same orientation with the groove between the seam in a few mm when the place the fully tiled and then let the adhesive cement reset (based on the duration of the adhesive cement select use) by during this should clean the tiles and then protected with a plastic POLYGENE SHEET and corrugated cardboard or plywood as but the weather the page so that the construction of the other sections can be made by the surface is not damaged

2.9 after the reset limestone, make the medication to prevent soil accumulation along the tiles by cleaning the seam of the cross contamination.

Note

- The use of adhesive cement should follow the way of the company for each manufacturer topology haste only by asking questions and learn how to use of the manufacturer and should be noticed that the adhesive cement select use has expired or by normal cement adhesive life will be approximately 3 months from the date of manufacture to use sticky notes to cement the expiration date may make the tiles that excessive corrosion in later

How to maintain and clean the floor tiles

to clean the floor tiles (Daily)

1. vacuum with no accumulated dust or dirt from the surface of the tiles, clean

2. Use the ม push the dust cloth ม must be clean spray push the cleaner on a cloth mopping brushes, spread across a piece of cloth with spray enough cloth finished, allow it to dry at least 3-6 hours or spray in the evening of the next morning. Then remove the mop the floor when mopping the floor and then start the cloth is dirty should change the new as soon as the cloth mop the floor should have multiple the use as the ม to clean cloth and can change the cloth.

3. If the debris can not rub the push the dust from the normal, use a clean cloth with water spot mop that is dirty if the wipe with a cloth moistened with water. Do not use the cleaning fluid and water based on the ratio specified in the label side of the bottle use sponge moistened with water and wipe the dirt is complete, and then use a clean damp cloth wipe out to remove the solution from sticking to the floor and then use a dry towel to dry immediately if you see a dirty, clean immediately should not leave it up to stains clean hard at a later time.

4. Do not use a solution containing the ingredients of the acid such as hydrochloric acid nitrous acid sulfuric acid hydrofluoric acid and chemical type of alcohol etc. to clean

5. Avoid using your device to clean the rough and sharp edges to protect the surface of the tile.

How to clean the floor tiles (Monthly)

1. Vacuum dust or dirt from the surface tiles to clean

2. Use the cleaning fluid and water based on the ratio specified in the label side of the bottle. Pour the mixture of water in the water spray and then spray on your skin. Use the tiles, sponge mop cleaning or use the brush to clean the brush a soft brush over the if soil that is not contrary to the first time, spray solution for 20 - 30 minutes solution to melt the stains out first and then make a contrary again at a point is dirty.

3. Use a clean damp cloth and wipe clean out from the floor and then use the clean water to rinse the floor again so that the solution from the floor, not to a sticky residue on the floor

4. Use a rubber mopping ironing water from the floor to the end and then use a dry cloth to wipe the floor, clean, dry immediately.

Note

- Monthly Cleaning may be made every 1 months, 3 months or 6 months depending on the condition of the page to the appropriate that should be within a few months

- every time a clean way to get wet with sanitizer solution must be clear off solution and wipe the floor dry immediately.